It is required to combine the factory standards and factory customary drawing methods that are not specified by the country, despite the fact that cable clamp pro it is drawn in accordance with the national drawing standards. This is the case even though it is drawn in accordance with the national drawing standards.

If the only mechanical processing that is performed after molding is burr repair, then the process drawing will be identical to the part drawing in every respect. This is because burr repair is the only mechanical processing that is performed. Drawing the process drawings on top of the drawing of the die-casting mold assembly is a common practice that is followed by many factories. It is recommended that you make an effort to have a ratio of one to one when you are drawing the assembly.

1.  Structural form of pouring system and exhaust system. You are not required to include the cavity height dimension; however, it should be marked. In addition to that, the overall dimensions of the mold ought to be mentioned. Complete the detailed list and the organization of all of the components by assigning numbers to each of them. It is important to take note of the technical requirements as well as the instructions for implementation.

2.  Requirements for die-casting mold assembly process. the fifth millimeter. On both the upper and lower sides of the mold, it is essential to make a note of the parallelism requirements that must be met. In addition to this, it is essential to emphasize the size that is established by the assembly process, as well as the requirements cable clamp pro that must be met concerning this size. There are a variety of requirements that fall under this category, including anti-oxidation treatment, die-casting mold numbering, engraving, marking, oil sealing, storage, and more.

There are certain requirements for the presentation, including the requirement of a proportional drawing and the allowance for either an increase or a decrease in size.

3. The order in which dimensions are marked is as follows: first, the dimensions of the main parts and the draft angle are marked, then the dimensions that match are marked, and finally, all of the dimensions are marked. The degree to which the surface is rough. It is recommended that the roughness that is utilized the most frequently be marked in the upper right corner of the drawing. Included in this package are activities such as checking for errors Die Casting Simulation Software, examining drawings, tracing drawings, and submitting drawings for publication.

Components that are made of plastic

In order to determine whether the flow of plastic material, shrinkage holes, weld marks, cracks, demoulding slope, and other factors have an effect on the performance, dimensional accuracy, surface quality, and other requirements of plastic parts, it is essential to analyze the data. Various tools and equipment for molding

For the purpose of determining whether the injection volume, injection pressure, and clamping force are sufficient, for the purpose of determining whether there are any problems with the installation of the mold, the core of the plastic parts, and the demoulding, and for the purpose of determining whether the nozzle of the injection machine and the mouth sleeve are in correct contact with one another. Important considerations include whether or not the method of demoulding is correct, whether or not the size, position, and quantity of the extension rod and push tube are appropriate, whether or not the push plate will be stuck by the core, and whether or not it will cause scratches on the molded parts.

The third step involves adjusting the temperature of the die-casting mold. With regard to the core-pulling mechanism of the inclined guide column, for instance, the question of whether or not the slider and push rod in the mechanism interfere with each other exists. If the pouring and exhaust systems are located in the appropriate location and are of the appropriate size, then this is an important consideration. Early versions of the design

1) Whether or not the order in which each mold part is depicted on the assembly drawing is appropriate, whether or not the representation is understandable, and whether or not there are any omissions. The part number and name, the production quantity, whether the part is made in-house or outsourced, whether it is a standard part Die Casting Simulation Software or a non-standard part, the processing accuracy of the parts, the correction processing and allowance of the high-precision dimensions of the molded plastic parts, and whether or not the material, heat treatment, surface treatment, and surface finishing degree of the mold parts are clearly marked and described are all important aspects to take into consideration. All of these characteristics are included on the drawing of the parts.

2)Make sure that the view position of all of the drawings of the parts and assembly is correct, that the projection is accurate, that the drawing method is in accordance with the national drawing standards, and that there are no dimensions that are missing. Examine the degree to which the processing is performing. Are you referring to the product's quality? Following the identification of the mistake, the mold will be repaired in order to rectify the situation going forward after it has been discovered.

There is a wide range of defects that can be discovered in plastic components, and the reasons that are responsible for these defects are also quite complicated. In addition to this, it is necessary to identify the factors that led to the defects in the plastic components and to propose possible solutions. As a general rule, the conditions under which the molding is performed should be changed first. This is because the conditions under which the molding is performed can be altered in a relatively straightforward manner. When the issue cannot be resolved by modifying the conditions of the molding process, the possibility of repairing the mold is taken into consideration as a potential solution.